Policy University Management WHS-PRO-012 Occupational Hygiene Management Procedure

WHS-PRO-012 Occupational Hygiene Management Procedure

Print Friendly and PDFPrint Friendly


It is the responsibility of a person conducting a business or undertaking to ensure that occupational exposures in the workplace do not exceed occupational exposure standards and are as low as reasonably practicable.

This document outlines the process for occupational hygiene management of health hazards in the workplace that can result in injury, illness, impairment, or affect the wellbeing of workers and members of the community.  Occupational hygiene hazards are normally divided into the categories of Biological, Chemical, Physical, Ergonomic and Psychosocial.   In particular the process for anticipation, recognition, evaluation, and control of health hazardous in the workplace.

The procedure outlines the process including:

  • Identifying occupational exposure hazards
  • Conducting risk assessment of occupational exposures
  • Complying with applicable exposure standards
  • Implementing control to reduce occupational exposures to acceptable levels


This procedure applies to all JCU workers, staff, faculty, students, adjuncts, volunteers and visitors conducting work with biological material.

This process is not intended to apply to potential public exposures or environmental harm.

This procedure is supported by the following JCU procedures:




Occupational Hygiene

The process of anticipation, recognition, evaluation, control of exposure to occupational hygiene hazards.  Occupational hygiene uses a combination of science, engineering and professional judgement in the process.

Physical Hazard

Hazards including radiation, temperature, noise and vibration.


Occupational exposure standard


Similar exposure group.  Used to define a group of workers that would be expected to have the same exposure to a physical or chemical hazard.  These groups will have similar tasks, frequency of tasks, controls and hazards.

Qualitative Exposure Assessment

Evaluation of potential personal exposure based on personal experience, and professional judgment.

Quantitative Exposure Assessment

Evaluation of actual personal exposure data using accepted numerical and mathematical analysis.

Route of Exposure

The route of exposure consisting of ingestion, inhalation,

Personal Monitoring

Measuring an individual’s exposure using a valid monitoring technique.  Example includes an inhalable dust sampling device situated in the breathing zone.

Environmental Measurement

Taking a measurement within the workplace using a suitable sampling device or measurement instrument.  Taking a temperature reading.

Static / Para Occupational Measurements

Taking samples or measurements within the working environment that will be used to determine potential for exposure.  This is not an actual exposure measurement.


1.     Duty, Obligations and Responsibilities

1.1   Vice Chancellor

1.2   Deputy Vice Chancellor / Director of Operations / College Managers / Directors / Deans / Managers / Academic Heads

1.3   Work Health and Safety Unit

1.4   Staff / Students / Adjuncts

2     Requirements

2.1  Occupational Hygiene Exposure

2.1.1 Initial Characterisation

2.2   Exposure Assessment

2.2.1 Additional Exposure Assessment

2.2.2 Exposure Assessment Monitoring Schedule

2.3  Occupational Hygiene Reports

2.4  Occupational Exposure Standards

2.4.1 Airborne Contaminants

2.4.2 Noise

2.4.3 Extended Working Shifts

2.4.4 Alternative Exposure Standard

2.5   Monitoring Methods

2.6   Equipment

2.7   Records

Related policy instruments

Schedules / Appendices


1   Duty, Obligations and Responsibilities

1.1 Vice Chancellor

  • The Vice Chancellor has overall responsibility to ensure the University is able to meet its WHS obligations, including the implementation of this procedure.

1.2 Deputy Vice Chancellor / Director of Operations/ College Managers / Directors/ Deans/ Managers/ Academic Heads

  • To ensure obligations under this procedure are met;
  • To support as required the identification, monitoring and control of occupational hygiene exposures within their work areas.

1.3 Work Health and Safety Unit

  • To conduct/facilitate the occupational hygiene monitoring program;
  • Engage/source specialist occupational hygiene advice as required;
  • Anticipate and identify occupational hygiene requirements.

1.4 Staff/Students/Adjuncts

  • To comply with this procedure;
  • To participate with any exposure monitoring that is conducted in the workplace;
  • Provide information as required in regard to potential occupational health exposures;
  • Notify the WHS unit where exposures have been identified that may require occupational hygiene monitoring.

2 Requirements

2.1 Occupational Hygiene Exposure Monitoring Program

The potential exposure of staff and students to occupational health hazards are to be risk assessed within the colleges and institutes.

Formal occupational hygiene evaluations shall be conducted where there is considered to be potential for acute or chronic health effects from exposure to chemical and physical agents.

An overall process of conducting an initial characterisation of occupational health hazards, is to be conducted (see Appendix 1 for flowchart).  This can be conducted using both qualitative and quantitative means to conduct assessment of potential exposures and development of monitoring and control plans where required.

2.1.1 Initial Characterisation for JCU Occupational Hygiene Monitoring Programs

The initial characterisation aims to determine potential exposures to occupational health hazards that require further monitoring/assessment due to likelihood for adverse health effects.  It takes the form of a qualitative risk assessment that may involve a walk-through of the workplace and preliminary measurement of exposure. The assessment will identify Similar Exposure Groups (SEGs) and a risk score for the potential to exceed the exposure standard.  This will determine the priority for further assessment.

The assessment process will:

  • Start at Divisional level and follow through to College/Research Group as appropriate;
  • Identify where potential exposures exist and define SEGs with occupational exposures that require further review/control, or no further action.

Potential occupational health hazards include:

  • Respirable dust;
  • Inhalable dust, including contaminants eg. lead;
  • Welding/soldering fume;
  • Asbestos;
  • Hazardous substances, eg. gas, vapour, liquid, solid;
  • Noise;
  • Vibration;
  • Extremes of temperature;
  • Non ionising radiation (UV, welding flash);
  • Ionising radiation (alpha, betta, gamma, x-ray);
  • Electromagnetic fields;
  • Biological hazards.

A qualitative risk assessment shall be performed to determine:

  • SEGS where no further action is required. This can include:
    • SEGS expected to be exposed to <10% of the relevant OES;
    • SEGS that are using known control banding techniques to result in very low; exposures.  Such as the use of fume cabinets during work with hazardous chemicals, or gas monitoring systems that are alarmed;
    • Risk assessments may not be recorded where there is not perceived to be a benefit, as in the potential for exposure is so low and infrequent;
  • SEGS that require further review and monitoring.  This can include:
    • SEGS expected to be exposed to >10% - <50% of the exposure standard;
    • SEGS expected to be exposed to >50% of the exposure standard;
    • SEGS where further review is required due to uncertainty;
    • SEGS or exposures that have legislative requirements to assess exposure;
  • SEGS that require immediate controls for unacceptable occupational exposures.  This will include:
    • SEGS expected to be exposed to >100% of the OES;
    • SEGS where occupational disease is reported.

The risk assessment will take into account:

  • Any existing exposure monitoring data;
  • Current control measures such as engineering controls or personal protective equipment;
  • Visual observation and other indicators of exposure potential;
  • Work practices;
  • Worker experience;
  • Legislative requirements for chemical and physical exposure hazards.

See Appendix 2 Qualitative Risk Rankings

The qualitative risk assessment will be recorded in an Excel matrix stored on the WHS Unit Corporate drive.

The document is to identify any relevant occupational hygiene monitoring reports or health monitoring results.

The assessment will be reviewed every five years or when a change occurs prompting the need for a review.

Notification of risk assessments that determine a need for exposure monitoring or assessment will be made to the WHS Biological, Radiation and Chemical Safety Advisor who will record the assessment in the Excel matrix and include it in the monitoring program. Notifications to the WHS Biological, Radiation and Chemical Safety Advisor will include the Riskware number.

2.2 Exposure Assessment

Exposure assessments may be conducted using a variety of techniques and over different time frames. Sampling methods include:

  • Personal monitoring, for example, sampling inhalable dust exposure within the workers breathing zone, or measuring noise exposure at the ear;
  • Static, para occupational monitoring or environmental monitoring, for example placing a gas monitor on a tripod or monitoring for asbestos fibres;
  • Monitoring survey, for example conducting a noise survey with a hand held sound level measuring device;
  • Biological monitoring, for example results from blood lead testing;
  • Health surveillance results.

Time frames include:

  • Grab sampling: very short-term sampling, typically within seconds.  Normally used to confirm the presence or identify a contaminant;
  • Short term sampling: sampling of 10 – 15 minutes.  This sampling can be compared with short term exposure limits (STEL).  A series of these short samples may be used to calculate full shift exposure;
  • Long term sampling: is typically conducted for either a full shift, or greater than half of a working shift.  This type of samplings is ideal for comparing to the 8 hour OES;
  • Continued sampling provides a real time measurement of exposure for the sampling period such as in the case of gas monitoring.  This method can provide a time weighted average (TWA) for the exposure period, peaks and STEL measurements in one method;
  • Concentration measurements can only provide an average result for the sampling periods such as in the case of inhalable dust monitoring.  STEL and TWA measurements will need to be taken as separate samples.

Ideally, sampling will be full shift, if this is not possible the next preferred method will be to ensure the full task is measured and appropriate estimation of exposure conducted.

2.2.1 Additional Exposure Assessment:

Where through other means such as risk assessments conducted within a Division/College/Research Group determines the need for additional exposure assessment, the additional exposure assessment will be recorded in the exposure monitoring schedule required by section 2.2.2 of this procedure.

Reasoning for additional exposure assessments may include:

  • Incidents;
  • New research;
  • New substances;
  • New equipment/plant;
  • Legislative changes;
  • Risk assessments including hazardous chemical risk assessments;
  • WorkCover claims;
  • Results of Health Surveillance;
  • Results from biological monitoring;
  • Requests.

2.2.2 Exposure Assessment Monitoring Schedule

A monitoring schedule will be produced from the information gained during the initial characterisation and risk assessment.  The schedule will also be updated as new exposure assessment issues are identified.

The monitoring schedule shall consist of:

  • Identification of the SEG to be monitored;
  • The type of exposure assessment to be conducted, such as personal monitoring survey;
  • Frequency of monitoring;
  • Record of a decision when monitoring is no longer required;
  • List of relevant reports/records for the SEG.

2.3 Occupational Hygiene Reports

Occupational hygiene reports prepared by JCU staff and contractors should address the headings provided below.  This includes:

  • Introduction – including date, location, person who commissioned the monitoring, aim of the monitoring;
  • Monitoring Methods and Equipment – sampling procedures, assessment standards applied, type of survey;
  • Analysis Method – analysis method and technical standard;
  • Occupational exposure standard – detail regarding the occupational exposure standard that results have been compared to;
  • Background – description of the process, task, history;
  • Results and discussion – results including date, sampling period, sample identifier, task description, monitoring period description, discussion of the results ;
  • Conclusions and recommendations – recommendations that apply the hierarchy of control;
  • Calibration certificates for instrumentation;
  • Analysis certificates;
  • Personal exposure summary for participants;
  • Separate results table with names of participants marked confidential to be supplied.

Note: Personal monitoring and static/survey results are to be presented in separate result tables.  Names of people monitored are not to appear in the body of reports.

Submit a draft report to the WHS Biological, Chemical and Radiation Safety Advisor for review prior to submitting a final report to the WHS Unit.

2.4 Occupational Exposure Standards

Occupational exposure standards (OES) are nominated for airborne contaminants and noise in Queensland. Where an OES is not legislated alternative sources will be researched.

The reasoning used to determine if exposure monitoring is required is found in section 5.1 of this procedure.

2.4.1 Airborne Contaminants

The “QLD Work Health and Safety Regulation 2011, Section 49” requires a person conducting a business or undertaking to ensure exposure standards for substances and mixtures are not exceeded.

Occupational Exposure standards are defined as:

  • Time Weighted Average (TWA).  This is a concentration of exposure for a period of eight hours;
  • Short Term Exposure Limitation (STEL).  This is a 15 minute TWA exposure limit which cannot be exceeded at any time during the working day.  The STEL exposure cannot last longer than a 15 minute period, which is not repeated more than four times during the shift.  There must also be at least a 60 minute interval between the exposures at the STEL;
  • Peak limitation.  This is the maximum airborne concentration of a particular substance determined over the shortest practicable period which does not exceed 15 minutes.    The peak limitation must not be exceeded at any time.

The Safe Work Australia document “Guidance on the Interpretation of exposure standards for Airborne Contaminants” should be consulted when interpreting exposure standards.

The occupational exposure standards can be found on the Safe Work Australia website’s Hazardous Chemical Information System (HCIS).

2.4.2 Noise

The “Qld Work Health and Safety Regulation 2011, Section 56, Part 4.1” states the occupational exposure standard for noise.  Consisting of:

  • LAeq,8h of 85 dB(A).  This is the sound pressure averaged over the time period;
  • LC, Peak of 140 dB(C).  This is an instantaneous level that can cause immediate damage to hearing.

2.4.3 Extended Working Shifts

When work shifts are longer than 8 hours, or working weeks longer than 5 days adjustments will be required to determine if an OES has been exceeded.   Airborne Contaminants

An 8 hour TWA occupational exposure standard is based on an 8 hour working day, 5 day working week. Where the length of a shift is longer than 8 hours, more than 5 days is worked in a row, or more than 40 hours is worked in a week, an adjustment to the TWA OES may be required.

The Australian Institute of Occupational Hygienists (AIOH) recommends using the Quebec model to adjust for extended shift arrangements.

In the case of JCU the majority of workers will work 8 hour shifts, five days a week.  In these cases the OES will not need adjustment.

The Safe Work Australia document Guidance on the Interpretation of exposure standards for Airborne Contaminants should be consulted when interpreting exposure standards to determine if shift adjustment is appropriate for the substance being monitored.

The Peak limitations cannot have any shift adjustment performed.   Noise

Where work shifts are longer than 8 hours, assessments of noise exposure (the measurement) must be normalised and adjusted as per AS:1269.1 (2005) to allow comparison with the LAeq,8h of 85 dB(A).

2.4.4 Alternative Exposure Standard

Where a Queensland or Australian OES does not exist, guidance from other sources may be used.

The source of the alternative OES should be a recognised government or professional agency.

Sources may include:

  • Australian New Zealand Standards;
  • Health and Safety Executive (United Kingdom);
  • Occupational Safety and health Administration (USA);
  • Australian Institute of Occupational Hygienists;
  • American Conference of Governmental Industrial Hygienists (USA).

2.5 Monitoring Methods

When occupational hygiene monitoring is conducted the method for measurement and analysis should be as stated in the relevant legislation or sourced from a recognised body.

Recognised monitoring methods and sources are include in the table below.

Occupational Monitoring Methods

Occupational Hygiene Hazard:

Source for Monitoring Method:

Occupational Noise

AS/NZS 1269.1:2005 Occupational noise management – Measurement and assessment of noise immission and exposure

Whole Body Vibration

AS/NZS 2670.1:2001Evaluation of human exposure to whole-body vibration

Inhalable Dust

AS 3640:2009 Workplace atmospheres – Method for sampling and gravimetric determination of inhalable dust

Respirable Dust

AS 2985:2009 Workplace atmospheres – Method for sampling and gravimetric determination of respirable dust

Various Airborne Chemical Hazards

Occupational Safety and Health Administration, Sampling and analytical Methods

Various Airborne Chemical Hazards

The National Institute for Occupational Safety and Health (NIOSH), Manual of Analytical Methods 4th Edition

Asbestos Fibre

Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Fibres 2nd Edition [NOHSC:3003(2005)]

2.6 Equipment

Occupational hygiene monitoring equipment will be maintained, serviced and calibrated as required by the manufacturer’s recommendations and the sampling methodology being applied.

A register of the occupational hygiene monitoring equipment used by the WHS Unit will be maintained on the WHS Unit corporate drive.

When equipment is hired, a copy of the calibration documentation will be obtained.

Copies of calibration certificates will be included in the report as an attachment.

2.7 Records

The following records will be retained:

  • Occupational hygiene monitoring reports;
  • Personal exposure letters/statements;
  • A record of exposure sampling is to be kept in a spreadsheet by the WHS Unit.  The record will include the date of sampling, monitoring conducted, and outcome/follow up.

A copy of records in relation to occupational hygiene monitoring shall be retained in accordance with the retention and disposal schedules governed by the Queensland State Archives:

  • General retention and disposal schedule;
  • University sector retention and disposal schedule.

WHS-PRO-002 Work Health and Safety Risk Management Procedure

WHS-PRO-008 Asbestos Management Procedure

WHS-PRO-009 Biosafety Procedure

WHS-PRO-010 Hazardous Chemicals Procedure

Safe Work Australia

Workplace Health and Safety

Australian Institute of Occupational Hygienists

Work Health and Safety Act 2011

Work Health and Safety Regulation 2011

AS/NZS 1269.1:2005 Occupational noise management – Measurement and assessment of noise immission and exposure

AS/NZS 2670.1:2001Evaluation of human exposure to whole-body vibration

AS 3640:2009 Workplace atmospheres – Method for sampling and gravimetric determination of inhalable dust

AS 2985:2009 Workplace atmospheres – Method for sampling and gravimetric determination of respirable dust

The National Institute for Occupational Safety and Health (NIOSH), Manual of Analytical Methods 4th Edition

Guidance Note on the Membrane Filter Method for Estimating Airborne Asbestos Fibres 2nd Edition [NOHSC:3003(2005)]

Managing Risks of Hazardous Chemicals in the Workplace Code of Practice 2021

Labelling of Workplace Hazardous Chemicals Code of Practice 2021

Managing Noise and Preventing Hearing Loss at Work Code of Practice 2021

Welding Processes Code of Practice 2021

Managing the Work Environment and Facilities Code of Practice 2021

How to Manage Work Health and Safety Risks Code of Practice 2021

Work Health and Safety Consultation, Co-operation and Co-ordination Code of Practice 2021


Appendix 1: Occupational Hygiene Monitoring Program Overview

Appendix 2: Qualitative Risk Rankings


NOTE:  Printed copies of this procedure are uncontrolled, and currency can only be assured at the time of printing.

Approval Details

Policy DomainUniversity Management
Policy Sub-domain WHS Management

Policy Custodian

Deputy Vice Chancellor, Services and Resources

Approval Authority

Work Health and Safety Committee

Date for next Major Review


Revision History


Approval date

Implementation date



21-1 25/11/2021 25/11/2021 Procedure reviewed, amendments to formatting and updated hyperlinks. WHS Biological, Radiation and Chemicals Safety Advisor




Minor update due to nomenclature changes due to renaming of Health Safety & Environment Unit to Work Health and Safety Unit

WHS Administrative Officer




Procedure established

HSE Biological, Radiation and Chemicals Safety Advisor

Contact person WHS Biological, Radiation and Chemicals Safety Advisor


Occupational; hygiene; noise; airborne; contaminants; OES; exposure standard; similar exposure group; STEL; asbestos; hazardous chemical; monitoring; health surveillance